The Effect of Reduction Rolls During the Milling Process on the Physicochemical Properties of Flour and Rheological Characteristics of Dough and Barbari Bread

Mirahmadi, Mahbobeh Sadat; Naghipour, Fariba; Seyedin Ardebili, Seyed Mehdi

doi:10.22101/JRIFST.2019.08.11.e1082

The Effect of Reduction Rolls During the Milling Process on the Physicochemical Properties of Flour and Rheological Characteristics of Dough and Barbari Bread

Document Type : Original Paper

Authors

¹ MSc. Student, Department of Food Science and Technology, Islamic Azad University, Science and Research Branch, Tehran

² Assistant Professor, Seed and Plant Improvement Institute, Agriculture Research, Education and Extension Organization (AREEO), Karaj, Iran

³ Assistant Professor, Department of Food Science and Technology, Islamic Azad University, Science and Research Branch, Tehran, Iran

10.22101/JRIFST.2019.08.11.e1082

Abstract

Reduction rolls play an important role in the process of flour production and increasing the quality of flour used in baking industry is considered as the most important factor to improve the qualitative and nutritional qualities of bread. So the aim of this study was to evaluate the effect of removing C1A, C1B, C2, C3 and C5 reduction rolls on the physicochemical properties of the flour and rheological properties of dough and the selection of the most effective rolls in milling process in a completely randomized design (p < /em>≤0.05). The results showed that two samples of flour that Also the sample, which C3 reduction rolls was removed, had the lowest gluten content (25%), gluten index (70), and zeleny sedimentation volume (17 mL). And the water absorption, development time, stability, and valorimeter number of the dough had the greatest reduction in this sample. Therefore, according to the results, it was found that by removing the C3 reduction roll in milling process, the physicochemical properties of the flour and the rheological properties of dough were strongly weakened. In the next step, the Barbari bread was produced by the flour obtained from this sample and control and its characteristics were examined. The results showed that the hardness of the sample by removing C3 reduction roll was higher (more than 35%) than the control sample during 2 and 72 h after baking. Also, the control had the highest score of overall acceptance in sensory evaluation. According to the results of this study, removing the C3 reduction roll, had the most effect on the quality of flour, dough and final product than the other roll in milling process.

Keywords

References

AACC. (2000). Approved methods of the American association of cereal chemists (Vol. 1): American Association of Cereal Chemists. St. Paul, MN.

Ahmadi Nodoushan, M. (2017). Technology Grain and its products (Vol. 2^nd Edition): Hamida Publications. (in Persian)

Akbari Rad, M., Najafian, G., Esmailzadeh Moghadam, M., & Khodarahmi, M. (2010). Study of genetic variation in baking quality related characteristics in bread wheat advanced lines and commercial cultivars. Iranian Society of Crops and Plant Breeding Sciences, 12(2),213-226. (in Persian)

Ali Akbarnia, E., & Azarbad, H. (2010). Flour milling technology from wheat to flour (Vol. 2^nd Edition ): Knowledge Frontier Publications. (in Persian)

Baines, Z. V., & Morris, E. R. (1987). Flavour/taste perception in thickened systems: the effect of guar gum above and below c. Food Hydrocolloids, 1(3), 197-205. doi:https://doi.org/10.1016/S0268-005X(87)80003-6

Baltensperger, W. (1993). New development in the mill flow charts grinding process using eight-roller mills. . Association of Operative Millers-Bulletin, 6327-6332.

Baltensperger, W. (2001). State-of-the-art grain milling technology. Association of Operative Millers-Bulletin (January), 7583-7591.

Baniasadi, A., Azizi, M. H., & Sahari, M. A. (2005). Determination of approperiate time of storage of some wheat varieties for increasing baking quality. Food Science and Technology, 2(6), 9-19.

Boland, A. B., Buhr, K., Giannouli, P., & Van Ruth, S. M. (2004). Influence of gelatin, starch, pectin and artificial saliva on the release of 11 flavour compounds from model gel systems. Food chemistry, 86(3), 401-411. doi:https://doi.org/10.1016/j.foodchem.2003.09.015

Cochet, S. (2012). From wheat to flour: Impact of starch damage on process and how to measure it. Chopin Inc. Presentation, IAOM Asia Pacific Manila, 2012.

Fatemi, H. (2004). Food chemistry (Vol. 4 Edition): Publication Joint Stock Company. (in Persian)

Fistes, A. Z. (2015). Comparative analysis of milling results on the tail-end reduction passages of the wheat flour milling process: conventional vs. eight-roller milling system/Uporedna analiza pokazatelja efektivnosti usitnjavanja osevaka na poslednjim prolazistima izmeljavanja u klasicnom i postupku sa primenom osmovaljne stolice. Hemijska Industrija, 69(4), 395-404. doi:https://doi.org/10.2298/HEMIND140211055F

Fišteš, A. Z., & Vukmirović, Đ. M. (2009). Reduction of wheat middlings using a conventional and eight-roller milling systems. Acta Periodica Technologica, 40, 25-34. doi:https://doi.org/10.2298/APT0940025F

Gilbert, J. (2002). Evaluation of flax and rice bran on physical and chemical properties of bread for achieving health benefits. (Unpublished master's thesis), Purdu University, West Lafayette,

Iranian National Standardization Organization. (2011a). Cereal and cereal products-Determination of moisture measure Cintent-Reference method. . (ISIRI Standard No, 2705, 1^stRevision). Retrieved from http://standard.isiri.gov.ir/StandardView.aspx?Id=46619 (in Persian)

Iranian National Standardization Organization. (2011b). Wheat flour- Specifications & test method. (IRISI Standard No. 103, 5^th. Revision). Retrieved from http://standard.isiri.gov.ir/StandardView.aspx?Id=41141 (in Persian)

Iranian National Standardization Organization. (2013). Floour from wheat (Triticum aestivum L.)- Amperometrivc method for starch damage measurment. (ISIRI Standard No. 16933, 1^st. Edition). Retrieved from http://standard.isiri.gov.ir/StandardView.aspx?Id=40897 (in Persian)

Jafari, M., Poormohammadi, K., & Asadpou, E. (2011). A Comprehensive Guide For the Quality Control of Wheat, Flour, and Bread (Vol. 1^stEdition): Food Industry Publications. (in Persian)

Kent, N. L., & Evers, A. (1994). Technology of cereals: an introduction for students of food science and agriculture. Oxford: Elsevier, Ltd.

MacRitchie, F. ( 1980). Studies of gluten protein from wheat flours. Cereal Food World, 25(7), 382-385.

Mohtarami, F., Esmaiili, M., Alizadeh Khaledabad, M., & Seyedain Ardabili, S. (2014). Improvement of the rheological properties of dough using transglutaminase and asparaginase enzymes, whey powder and inulin. Iranian Food Science and Technology Research Journal, 11(4), 445-457. doi:https://doi.org/10.22067/ifstrj.v1394i11.30710 (in Persian)

Moradi, V., Ghiassi Tarzi, B., Seyyedain Ardebili, S. M., & Azizinejad, R. (2010). The assessment and comparison of the quality of iranian commercial flours glutens by alveograph and farinograph methods. Food Technology & Nutrition, 7(2), 51-78. (in Persian)

Opáth, R. (2014). Technical exploitation parameters of grinding rolls work in flour mill. Research in Agricultural Engineering, 60(Special Issue), S92-S97.

Owens, W. (2001). Wheat, corn and coarse grains milling. In W. G. Owens (Ed.), Cereals processing technology (pp. 27-52): Wood head Publishing Ltd.

Peighambardoust, S., Van Brenk, S., Van der Goot, A., Hamer, R., & Boom, R. (2007). Dough processing in a Couette-type device with varying eccentricity: Effect on glutenin macro-polymer properties and dough micro-structure. Journal of cereal science, 45(1), 34-48. doi:https://doi.org/10.1016/j.jcs.2006.05.009

Peighambardoust, S. H. (2006). Development of dough under shear flow. (Doctoral issertation), Wageningen Wageningen, the Netherlands.

Peighambardoust, S. H. (2017). Rheology Test Methods: Wheat, Flour and Dough: Amidi Publications. (in Persian)

Posner, E. S. (2000). Wheat. In K. Kulp, G. joseph, & J. G. Ponte (Eds.), Handbook of Cereal Science and Technology (Vol. 2^nd Edition, pp. 1-30). New York: Marcel Dekker, CRC Press.

Pourfarzad, A., Khodaparast, M. H. H., Karimi, M., Mortazavi, S. A., Davoodi, M. G., Sourki, A. H., & Razavizadegan Jahromi, S. H. (2011). Effect of polyols on shelf-life and quality of flat bread fortified with soy flour. Journal of Food Process Engineering, 34(5), 1435-1448. doi:https://doi.org/10.1111/j.1745-4530.2009.00541.x

Scanlon, M., Dexter, J., & Biliaderis, C. (1988). Particle-size related physical properties of flour produced by smooth roll reduction of hard red spring wheat farina. Cereal Chem, 65(6), 486-492.

Shahedi, M., Kabir, G., & Bahrami, M. (2005). Flour quality andices and dough rheological properties of Iranian wheats for production of taftoon bread. Journal of Agricultural Sciences and Natural Resources, 12(2), 78-88. (in Persian)

Shekholeslami, Z., & Karimi, M. (2012). Effect of Soaked Bran, Wheat Malt Flour and Sourdough on Reducing Phytic Acid in Barbari Bread. Journal of Agricultural Engineering Research, 13(2), 97-108. doi:https://doi.org/10.22092/jaer.2012.100275 (in Persian)

Stone, H., & Sidel, J. (2004). Sensory Evaluation Practices, Elsevier Academic Press. California, USA, 20-45.

William, R., El-Haramein, F., Nakkoul, H., & Rihawi, S. (1986). Crop Quality Evaluation Methods and Guidelines. Technical Manual No. 16. International Center for Agricultural Research in the Dry Areas (ICARDA), PO Box 5466.